XTREMESTRIP™
Part Number: SDT-110
Military Specification: None

XtremeStrip™ is a fast acting remover of varnish paint, enamels, lacquer, shellac, glue and mastic.  XtremeStrip™ is a very fluid – “water like” – stripper that makes an excellent dip tank stripper. It is formulated to be applied on flat surfaces – like floors.  XtremeStrip™ will not raise the grain or discolor the finest woods. After stripping the coating on the substrate, it is not necessary to neutralize the surface with water before coating the stripped surface.

LYFT-OFF™
Part Number: PTS-202
Military Specification: TT-R-2918A TYI

PTS-202™ is a biodegradable peroxide based paint remover that is formulated to remove the most resilient coatings from metal and composite surfaces that conforms with military specification TT-R-2918A TYI.  This is a stable paint remover that will not corrode the metal.  PTS-202 works by breaking through the film of the paint and lifting the paint off in sheets instead of turning the paint to sludge.  This remover is easy and safe to use as well as clean up.

‍

CAMA™ - CERTIFIED AIRCRAFT - MARINE - AUTOMOTIVE

Part Number: PTS-294
Military Specification: MIL-R-81294D TYI & TYII CL. 2A

CAMA™ (PTS-294) meets Military Specification: MIL-R-81294D TYI & TYII CL. 2A.  The Certified Aircraft, Marine & Automotive Paint Remover (CAMA™) is a non-flammable fast acting Urethane, Epoxy and Marine finish remover.  CAMA™ is scientifically formulated to remove the most difficult surface coatings and stains.  Wash away action with water forms a foamy emulsion to get cracks, seems, moldings and crevices clean.  This product is viscous and formulated to cling to vertical surfaces.

‍

PT-799 - POLYURETHANE
Part Number: PT-799 (PLUS COLOR#)
Military Specification: MIL-PRF-85285D/E Type I, II & IV Class H. This coating is on the NAVY QPD (Qualified Products Database) for TY I, II & IV (gloss only)

PT-799 Polyurethane is a high performance, two-component, polyurethane topcoat designed for exterior use on high performance, general aviation, business jet, and commercial aircraft.  This coating is also used widely for industrial, oil and gas as well as by original equipment manufacturers. These high performance coatings have excellent resistance to hydraulic jet fluid, fuel, crude oil, impact, salt and ultraviolet rays.  PT-799 Polyurethane is extremely durable with excellent color and gloss retention.

PT-799 Conductive Black is also available.  It is formulated as an electrically conductive paint which can be used for coating and sealing non-metallic surfaces by brushing or spraying. The Conductive Coating is intended for use where an electrostatic discharge path is required for electrical continuity on non-metallic substrates.

‍

PT-110 ACRYLIC LACQUER
Part Number: PT-110 (PLUS COLOR #)
Military Specification: MIL-L-81352A, BELL HELICOPTER SPECIFICATION 299-947-069.

PT-110 is a general purpose high performance, single component acrylic lacquer topcoat designed for interior or exterior use on metal or composite surfaces.  PT-110 meets and exceeds MIL-L-81352A and the Bell Helicopter Specification 299-947-069.  This product is available in bulk and aerosol cans.

‍

PT-355 ENGINE ENAMEL
Part Number: PT-355
Military Specification: NOT A MIL-SPEC

PT-355 Engine Enamel is a heat resistant enamel packaged in bulk or aerosol cans.  It is intended for use over metal surfaces that can withstand temperatures of 500°F. Although some colors will darken at this temperature, the integrity of the coating will remain intact. The Engine Enamel can be applied over bare, scuffed, sanded, abrasive blasted, primed and previously painted surfaces and shows excellent protection.

‍

PT-426F LOW VOC EPOXY TOPCOAT
Part Number: PT-426F & G (COLOR#)
Military Specification: PT-426F – MIL-PRF-22750E, F & G Type I CL H GRADE B as well as BMS 10-11V Type II

PT-426F – MIL-PRF-22750E, F & G Type I CL H GRADE B as well as BMS 10-11V Type II are high performance, two component catalyst cure epoxy topcoats designed for interior and exterior use on high performance aviation/aerospace, industrial, and marine applications. PT-426G Series Epoxy meets, and exceedsThis high performance coating contains no substance of known toxicity (under normal usage conditions) and provides ultimate protection. These epoxy topcoats provide a high quality finish to metal, wood, and most other materials capable of being coated and offer excellent chemical resistance properties.

‍

TTE ENAMEL TOPCOAT SERIES
Part Number: PT-381 ENAMEL TOPCOAT, PT-382 ENAMEL TOPCOAT, PT-383 ENAMEL TOPCOAT (PLUS COLOR#)
Military Specification: PT-381 is TT-E-489J. PT-382 is TT-E-529G & A-A-2962, PT-383 is TT-E-527D

Our “TTE” enamel coatings are high performance, single component enamel topcoats designed for interior use on high performance general aviation, business jet, and commercial aircraft.  These coatings are excellent exterior coatings on substrates that are not subjected to harsh environments.  PT-381 enamel meets, and exceeds TT-E-489J (Gloss only).  PT-382 enamel meets and exceeds TT-E-529G & A-A-2962 (semi-gloss only) and PT-383 (flat only)enamel meets and exceeds TT-E-527D These high performance coatings can be applied over wood, composite or metal surfaces.   These products are available in bulk or aerosol.

‍

PT-605 ANTI-SEIZE COMPOUND
Part Number: PT-605
Military Specification: NOT A MIL-SPEC COATING

PT-605 Anti-Seize Compound is a silicone based grease with a high pigmentation of microfine molybdenum disulfide.  It is heat stable and will not decompose or form a gum deposit.  It is effective under light or medium bearing loads on steel to bronze, metal babbitt, zinc, nylon, Teflon or hard-anodized aluminum surfaces.  PT-605 is an  EXTREME PRESSURE grease that protects from galling, seizing and fretting.  Also this product is virtually waterproof which helps to provide excellent rust and corrosion protection.  Normally it is suitable for operating temperatures of  -65° F to +1000° F.  This product is best used as a lubricant for gaskets threads, parts and gears that are exposed to excessive temperatures ranges.

‍

PT-101 MOLY SPRAY
Part Number: PT-101
Military Specification: NOT A MIL-SPEC COATING

Moly spray is unequaled as a lubricant for machine tools, plastic molding machines, paper and textile making equipment, oven mechanisms, and sheet metal and tube bending operations.  It is highly recommended for use wherever pressures or temperatures are extreme or environmental conditions render liquid lubricants undesirable.  In field tests, Moly Spray has proven superior for widely diversified uses.  It is outstanding in numerous industrial and military applications including automobile mechanisms, sporting equipment, office machines, lathes, milling machines, planers, presses, chucks, arbors, bearings, universal joints and controls, and adjustments.  Moly Spray is also effective in broaching cold swaging, drawing, stretching, forming, and press-fit operations.  Moly Spray excels as a lubricant, anti-galling, or separating agent on steel, steel alloys, cast iron, aluminum or aluminum alloys, copper alloys, lead and zinc alloys, titanium, wood, rubber, plastics, ceramics and glass.

PT-650 TOOTH MARKING GREASE
Part Number: PT-650
Military Specification: NOT A MIL-SPEC COATING

PT-650 Tooth Marking Grease is an ester based oil with high pigmentation loading.  Although PT-650 has the consistency of a thick paste, it may be thinned or thickened to meet your requirements.  PT-650 is a lubricant for marking teeth on gears to enable one to determine when maintenance is necessary.

PT-14 MICROFINE TECHLUBE (W GRAPHITE), PT-17 MICROFINE TECHNLUBE
Part Number: PT-14, PT-17
Military Specification: PT-14 IS NOT A MIL SPEC COATING, PT-17 IS MIL-L 46010 TY II

These dry film lubricants are intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.

PT-14 is a microfine Molybdenum Disulphide with graphite in a multi-polymer thermosetting resin binder.  PT-14 is supplied in concentrate form requiring reduction with PT-1002 solvent.  PT-14 is designed for operating temperatures from -100F too +500F.

PT-17 is a microfine Molybdenum Disulphide (no graphite) in a multi-polymer thermosetting resin binder 9.  PT-17 is supplied in concentrate form requiring reduction with PT1002 solvent.  PT-17 is designed for operating temperatures between -300F and +500F.  Meets MIL-L 46010 TY II.

‍

PT-14 MICROFINE TECHLUBE (W GRAPHITE), PT-17 MICROFINE TECHNLUBE
Part Number: PT-14, PT-17
Military Specification: PT-14 IS NOT A MIL SPEC COATING, PT-17 IS MIL-L 46010 TY II

These dry film lubricants are intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.

PT-14 is a microfine Molybdenum Disulphide with graphite in a multi-polymer thermosetting resin binder.  PT-14 is supplied in concentrate form requiring reduction with PT-1002 solvent.  PT-14 is designed for operating temperatures from -100F too +500F.

PT-17 is a microfine Molybdenum Disulphide (no graphite) in a multi-polymer thermosetting resin binder 9.  PT-17 is supplied in concentrate form requiring reduction with PT1002 solvent.  PT-17 is designed for operating temperatures between -300F and +500F.  Meets MIL-L 46010 TY II.

‍

PT-24M MICROFINE TECHLUBE, PT-24G MICROFINE TECHNLUBE (w/graphite)
Part Number: PT-24M, PT-24G
Military Specification: NOT MIL SPEC COATINGS

PT-24M is a Molydbenum Disolphide in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals.  The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity.  PT-24M has been proven to be the product for high temperature and high speed dry film lubrication.  This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.

PT-24G is a Graphite pigment in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals.  The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity.  PT-24G has been proven to be the product for high temperature and high speed dry film lubrication.  This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.

‍

‍

PT-24M MICROFINE TECHLUBE, PT-24G MICROFINE TECHNLUBE (w/graphite)
Part Number: PT-24M, PT-24G
Military Specification: NOT MIL SPEC COATINGS

PT-24M is a Molydbenum Disolphide in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals.  The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity.  PT-24M has been proven to be the product for high temperature and high speed dry film lubrication.  This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.

PT-24G is a Graphite pigment in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals.  The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity.  PT-24G has been proven to be the product for high temperature and high speed dry film lubrication.  This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.

‍

‍

POLYKICK™ ACCELERATOR
Part Number: POLYKICK™
Military Specification: NOT A MIL-SPEC COATING

Polykick™ is a paint additive formulated by Products Techniques Inc. to accelerate the air dry time of two component polyurethane topcoat systems.   While this product reduces dry times it will not accelerate chemical cure rates.  A full chemical cure for two component polyurethane systems typically takes 4 to 7 days.  Polykick™ will accelerate the dry time of any two component polyurethane system not just PTI’s coatings.

‍

NO POP™ RETARDER
Part Number: NO POP™
Military Specification: NOT A MIL-SPEC COATING

No Pop™  is a specially formulated additive. When paint is applied, particularly by spraying, the solvents that carry the resin and the pigments “flash off” – evaporate.  This product is used to slow that process particularly in hot and humid weather.  This allows the paint to flow evenly and prevents a condition known as “solvent pop”—the formation of small air bubbles on the surface of the paint.  It also prevents a condition known as “dry spray”—solvent evaporating before the paint hits the surface of the substrate.  So, No Pop™   keeps the material wet allowing it to flow, dry, and cure as it should.

‍

NO PEEL™
Part Number: PT-900
Military Specification: NOT A MIL-SPEC COATING

No Peel™ – PT-900 is formulated to enable epoxy and polyurethane topcoats flow evenly despite certain surface defects or contaminants.  This additive helps prevent “Orange Peel”—the pitting in paint caused by contaminants on the substrate’s surface or in the spray gun. No Peel™ is flow additive.

‍