CLOSE ✕
Get in Touch
Thank you for your interest! Please fill out the form below if you would like to work together.

Thank you! Your submission has been received!

Oops! Something went wrong while submitting the form

PT-110 ACRYLIC LACQUER

CALL FOR COLORS
|
FINISH COATINGS
|
PT-110
PT-110
PT-110 ACRYLIC LACQUER

PT-110 ACRYLIC LACQUER
Part Number: PT-110 (PLUS COLOR #)
Military Specification: MIL-L-81352A, BELL HELICOPTER SPECIFICATION 299-947-069.

PT-110 is a general purpose high performance, single component acrylic lacquer topcoat designed for interior or exterior use on metal or composite surfaces.  PT-110 meets and exceeds MIL-L-81352A and the Bell Helicopter Specification 299-947-069.  This product is available in bulk and aerosol cans.

PRODUCT SPECIFICATIONS
PTI PART NUMBER
PT-110
PRODUCT TYPE:
FINISH COATINGS
COLOR:
CALL FOR COLORS
BMS SPECIFICATION:
NONE
MIL-SPEC:
MIL-L-81352A
OTHER SPECIFICATIONS
Bell Helicopter Specification 299-947-069
UNIT SIZE
NONE

Extended Description

PT-110 is a general purpose high performance, single component acrylic lacquer topcoat designed for interior or exterior use on metal or composite surfaces. PT-110 meets and exceeds MIL-L-81352A and the BELL HELICOPTER SPECIFICATION 299-947-069. This product is available in bulk and aerosol cans.

COLORS

This coating can be provided in any color & gloss range as designated by the Federal Standard 595C. Custom colors are also available.

COATING PROPERTIES & CHARACTERISTICS

  • Flash Point :76°F
  • Reducer: PT-1002 or PT-1003 TYIII Primer PT-562 & PT-500
  • Recommended Dry Film Thickness: 1 mil
  • Weight (lbs per gallon): 9 to 11 lbs
  • Theoretical Coverage: 300 sq. ft./gallon

SHELF LIFE

Shelf life is only applicable for materials stored in unopened and undamaged original factory filled containers.1 year when stored between 50⁰-85⁰ Fahrenheit.

APPLICATION

This product can be applied by brushing, rolling, conventional air spray equipment or a HVLP spray system. Please consult with a PTI representative for specific equipment recommendations and settings.

  1. Make sure pots, guns, and lines are purged and cleaned.
  2. Mix both paint and reducer thoroughly and filter/strain before spray application. NOTE: It is not recommended to strain flat/matte coatings.
  3. HVLP Spray Pressure: 7-10psi. Conventional spray pressure 15-30psi
  4. Always air-blow and tack wipe the surfaces to be painted. Aircraft should be grounded to prevent static.
  5. Best application results: apply 2 coats: 1 fog/tack coat & 1 full coat from 0.6 – 1 mil thickness.
  6. Do not allow more than 12 hours to pass before applying the second coat.
  7. Recommended Dry Film Thickness is 1-1.2 mils. Some colors may require thicker films to achieve hiding.

NOTE: Application of PTI products requires the use of all OSHA approved safety equipment, including proper ventilation. Additionally, PTI products require the recommended temperature/humidity conditions and film thickness ranges for optimal performance.

DRYING & CURING SCHEDULE

Dry times are based on the dry film thickness between 1-1.2 mils (25-50 microns). Air Dry Times Times are based on laboratory temperatures (75⁰F / 25⁰C and 50% Relative Humidity). It is recommended that temperatures are between 50 and 95 deg. F and humidity does not exceed 75%.

Dries hard in 10 minutes minutes; full cure in 72 hours.

Force Cure:

Air dry for 10 minutes, then bake for no longer than 1 hour at 120°F. After heat, let parts return to ambient temperature for a minimum of 1 hour.

Questions About Our Products?
Contact PTI

More PTI Products

TTE ENAMEL TOPCOAT SERIES
Part Number
PT-381, 382, 383 ENAMEL TOPCOAT
BMS Specification
NONE
NONE
Color
CALL FOR COLORS
NONE
Mil-Spec
PT-381 is TT-E-489J. PT-382 is TT-E-529G & A-A-2962, PT-383 is TT-E-527D