.svg)
INSIGNIA WHITE BUTYRATE DOPE
ISOPROPYL ALCOHOL 99%
JUNEAU WHITE BUTYRATE DOPE
KOTT S-6 REDUCER/THINNER
LACQUER ACRYLIC (FOR WEAPONS SYSTEMS)
LACQUER CAMOUFLAGE
LACQUER THINNER
LACQUER, ACRYLIC NITROCELLULOSE GLOSS (FOR AIRCRAFT, S/S MIL-L-81352
LACQUER, BRUSHING, CLEAR & PIGMENTED FOR INTERIOR & EXTERIOR
LACQUER, CELLULOSE NITRATE (FOR AIRCRAFT USE & SMALL ARMS)
LACQUER, NITROCELLULOSE, ACRYLIC AND ACRYLIC BUTYRATE, AEROSOL
LACQUER, NITROCELLULOSE, ACRYLIC AND ACRYLIC BUTYRATE, AEROSOL
LACQUER, NITROCELLULOSE, ACRYLIC AND ACRYLIC BUTYRATE, AEROSOL
LACQUER, PIGMENTED FOR INTERIOR SPRAYING (S/S A-A-3003)
LEAD & CHROMATE FREE EPOXY PRIMER
LIACQUER THINNER
LIFT-OFF BIODEGRADABLE PAINT REMOVER
LOW VOC ENAMEL, ALKYD, GLOSS TOPCOAT
LOW VOC ENAMEL, ALKYD, GLOSS TOPCOAT
LOW VOC ENAMEL, ALKYD, LUSTERLESS (FLAT) TOPCOAT
LOW VOC ENAMEL, ALKYD, SEMIGLOSS TOPCOAT
LOW VOC PRIMER, CHROMATE FREE
LYFT-OFF™
Part Number: PTS-202
Military Specification: TT-R-2918A TYI
PTS-202™ is a biodegradable peroxide based paint remover that is formulated to remove the most resilient coatings from metal and composite surfaces that conforms with military specification TT-R-2918A TYI. This is a stable paint remover that will not corrode the metal. PTS-202 works by breaking through the film of the paint and lifting the paint off in sheets instead of turning the paint to sludge. This remover is easy and safe to use as well as clean up.
MARKING STENCIL INK
MEDIUM EVAPORATING THINNER/REDUCER
METHANOL (METHYL ALCOHOL) SOLVENT
METHYL ETHYL KETONE SOLVENT
METHYLENE CHLORIDE TECHNICAL GRADE SOLVENT
MINERAL SPIRITS SOLVENT/THINNER
MODIFIED ACRYLIC
MODIFIED ACRYLIC, TWO COMPONENT
MOISTURE & FUNGUS RESISTANT VARNISH FOR ELECTIRCAL EQUIP.
MOLYBDENUM DISULFIDE, TECHNICAL, LUBRICATION GRADE
NAPHTHA ALIPHATIC
NAPHTHA SOLVENT
NITRATE DOPE CLEAR
NITRATE DOPE REJUVENATOR
NITRATE DOPE THINNER
NITRATE RETARDER
NO PEEL™
Part Number: PT-900
Military Specification: NOT A MIL-SPEC COATING
No Peel™ – PT-900 is formulated to enable epoxy and polyurethane topcoats flow evenly despite certain surface defects or contaminants. This additive helps prevent “Orange Peel”—the pitting in paint caused by contaminants on the substrate’s surface or in the spray gun. No Peel™ is flow additive.
NO POP™ RETARDER
Part Number: NO POP™
Military Specification: NOT A MIL-SPEC COATING
No Pop™ is a specially formulated additive. When paint is applied, particularly by spraying, the solvents that carry the resin and the pigments “flash off” – evaporate. This product is used to slow that process particularly in hot and humid weather. This allows the paint to flow evenly and prevents a condition known as “solvent pop”—the formation of small air bubbles on the surface of the paint. It also prevents a condition known as “dry spray”—solvent evaporating before the paint hits the surface of the substrate. So, No Pop™ keeps the material wet allowing it to flow, dry, and cure as it should.
NON-TAUTENING BUTYRATE DOPE
NON-TAUTENING NITRATE DOPE CLEAR
NORMAL BUTYL ACETATE SOLVENT
NORMAL BUTYL ALCOHOL SOLVENT
#175 AQUA STRIP
BUTYRATE REJUVENATOR
SDT-110 FLOOR AND DIP TANK STRIPPER
STRIPPER-B FLOOR AND DIP TANK STRIPPER
PERMANENT PHENOLIC FOR ENGINE COMPONENTS
PLAIN WHITE BUTYRATE DOPE
POLY-VINYL COPOLYMER CIRCUIT BOARD COATING
COATING, WATERBORNE POLYURETHANE FOR AIRCRAFT USE
POLYKICK™ ACCELERATOR
Part Number: POLYKICK™
Military Specification: NOT A MIL-SPEC COATING
Polykick™ is a paint additive formulated by Products Techniques Inc. to accelerate the air dry time of two component polyurethane topcoat systems. While this product reduces dry times it will not accelerate chemical cure rates. A full chemical cure for two component polyurethane systems typically takes 4 to 7 days. Polykick™ will accelerate the dry time of any two component polyurethane system not just PTI’s coatings.
POLYURETHANE ACCELERATOR
ALUMINUM PASTE
POLYURETHANE AND ACRYLIC THINNER
POLYURETHANE CLEAR COATING
COATING COMPOUND, NON-SLIP, WALK WAY & WING WALK
POLYURETHANE FOR AIRCRAFT AND SUPPORT EQUIPMENT
POLYURETHANE FOR AIRCRAFT AND SUPPORT EQUIPMENT
POLYURETHANE FOR AIRCRAFT AND SUPPORT EQUIPMENT, HIGH SOLIDS
POLYURETHANE PRIMER
POLYURETHANE THINNER
PRIMER FOR SHIPBOARDS, VINYL-ZINC CHROMATE
PRIMER ZINC MOLYDBATE ALKYD TYPE
PRIMER, CELLULOSE-NITRATE MODIFIED ALKYD, CORROSION-INHIBITING, FAST DRYING ( SPRAY APPLICATION OVER PRETREATMENT COATING)
PRIMER, ZINC MOLYBDATE, ALKYD TYPE
PRIMER, ZINC PHOSPHATE, ALKYD FOR GENERAL USE/ALL-PURPOSE
PT-101 MOLY SPRAY
Part Number: PT-101
Military Specification: NOT A MIL-SPEC COATING
Moly spray is unequaled as a lubricant for machine tools, plastic molding machines, paper and textile making equipment, oven mechanisms, and sheet metal and tube bending operations. It is highly recommended for use wherever pressures or temperatures are extreme or environmental conditions render liquid lubricants undesirable. In field tests, Moly Spray has proven superior for widely diversified uses. It is outstanding in numerous industrial and military applications including automobile mechanisms, sporting equipment, office machines, lathes, milling machines, planers, presses, chucks, arbors, bearings, universal joints and controls, and adjustments. Moly Spray is also effective in broaching cold swaging, drawing, stretching, forming, and press-fit operations. Moly Spray excels as a lubricant, anti-galling, or separating agent on steel, steel alloys, cast iron, aluminum or aluminum alloys, copper alloys, lead and zinc alloys, titanium, wood, rubber, plastics, ceramics and glass.
PT-110 ACRYLIC LACQUER
Part Number: PT-110 (PLUS COLOR #)
Military Specification: MIL-L-81352A, BELL HELICOPTER SPECIFICATION 299-947-069.
PT-110 is a general purpose high performance, single component acrylic lacquer topcoat designed for interior or exterior use on metal or composite surfaces. PT-110 meets and exceeds MIL-L-81352A and the Bell Helicopter Specification 299-947-069. This product is available in bulk and aerosol cans.
PT-14 MICROFINE TECHLUBE (W GRAPHITE), PT-17 MICROFINE TECHNLUBE
Part Number: PT-14, PT-17
Military Specification: PT-14 IS NOT A MIL SPEC COATING, PT-17 IS MIL-L 46010 TY II
These dry film lubricants are intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.
PT-14 is a microfine Molybdenum Disulphide with graphite in a multi-polymer thermosetting resin binder. PT-14 is supplied in concentrate form requiring reduction with PT-1002 solvent. PT-14 is designed for operating temperatures from -100F too +500F.
PT-17 is a microfine Molybdenum Disulphide (no graphite) in a multi-polymer thermosetting resin binder 9. PT-17 is supplied in concentrate form requiring reduction with PT1002 solvent. PT-17 is designed for operating temperatures between -300F and +500F. Meets MIL-L 46010 TY II.
PT-14 MICROFINE TECHLUBE (W GRAPHITE), PT-17 MICROFINE TECHNLUBE
Part Number: PT-14, PT-17
Military Specification: PT-14 IS NOT A MIL SPEC COATING, PT-17 IS MIL-L 46010 TY II
These dry film lubricants are intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.
PT-14 is a microfine Molybdenum Disulphide with graphite in a multi-polymer thermosetting resin binder. PT-14 is supplied in concentrate form requiring reduction with PT-1002 solvent. PT-14 is designed for operating temperatures from -100F too +500F.
PT-17 is a microfine Molybdenum Disulphide (no graphite) in a multi-polymer thermosetting resin binder 9. PT-17 is supplied in concentrate form requiring reduction with PT1002 solvent. PT-17 is designed for operating temperatures between -300F and +500F. Meets MIL-L 46010 TY II.
PT-24M MICROFINE TECHLUBE, PT-24G MICROFINE TECHNLUBE (w/graphite)
Part Number: PT-24M, PT-24G
Military Specification: NOT MIL SPEC COATINGS
PT-24M is a Molydbenum Disolphide in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals. The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity. PT-24M has been proven to be the product for high temperature and high speed dry film lubrication. This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.
PT-24G is a Graphite pigment in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals. The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity. PT-24G has been proven to be the product for high temperature and high speed dry film lubrication. This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.
PT-24M MICROFINE TECHLUBE, PT-24G MICROFINE TECHNLUBE (w/graphite)
Part Number: PT-24M, PT-24G
Military Specification: NOT MIL SPEC COATINGS
PT-24M is a Molydbenum Disolphide in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals. The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity. PT-24M has been proven to be the product for high temperature and high speed dry film lubrication. This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.
PT-24G is a Graphite pigment in a multi-polymer bake cure resin binder. This product contains laminar solids and soft metals. The soft metals are employed to improve wear characteristics under certain conditions that are largely determined by electrical and thermal conductivity. PT-24G has been proven to be the product for high temperature and high speed dry film lubrication. This dry film lubricant is intended to be applied to equipment such as but not limited to steel, aluminum, magnesium, clutches, gears, shafts and other mechanical parts which function under extreme weathering and/or operating conditions.
PT-355 ENGINE ENAMEL
Part Number: PT-355
Military Specification: NOT A MIL-SPEC
PT-355 Engine Enamel is a heat resistant enamel packaged in bulk or aerosol cans. It is intended for use over metal surfaces that can withstand temperatures of 500°F. Although some colors will darken at this temperature, the integrity of the coating will remain intact. The Engine Enamel can be applied over bare, scuffed, sanded, abrasive blasted, primed and previously painted surfaces and shows excellent protection.
PT-402 ACID ETCHING PRIMER
Part Number: PT-402 (YELLOW OR GREEN)
Military Specification: DOD-P-15328D, MIL-C-8514C-PT-1045 Reducer
PT-402 Acid Etching Primer, when properly reduced with PT-1045 Reducer, meets and exceeds MIL-C-8514C. PT-402is a polyvinyl butyral zinc chromate formulation that may be used to prime all plain or plated metallic surfaces. Priming surfaces with PT-402 Acid Etching Primer prior to priming with epoxy primer MIL-PRF-23377 or by itself will ensure maximum adhesion and protection of all bake or air-dry finish coats (including lacquer finish coats). The finely ground emulsions of zinc chromate pigments, resins and phosphoric acid hardeners are virtually non-settling. Once applied, the Acid Etching Primer requires no sanding and has a pot life of 8 hours. Extreme humidity can affect the bonding of the coating.
PT-426F LOW VOC EPOXY TOPCOAT
Part Number: PT-426F & G (COLOR#)
Military Specification: PT-426F – MIL-PRF-22750E, F & G Type I CL H GRADE B as well as BMS 10-11V Type II
PT-426F – MIL-PRF-22750E, F & G Type I CL H GRADE B as well as BMS 10-11V Type II are high performance, two component catalyst cure epoxy topcoats designed for interior and exterior use on high performance aviation/aerospace, industrial, and marine applications. PT-426G Series Epoxy meets, and exceedsThis high performance coating contains no substance of known toxicity (under normal usage conditions) and provides ultimate protection. These epoxy topcoats provide a high quality finish to metal, wood, and most other materials capable of being coated and offer excellent chemical resistance properties.
PT-500GIC EPOXY PRIMER
Part Number: PT-500KIC2 TYI CL. C2
Military Specification: MIL-PRF-23377 Rev. F, G, H, J & K TY. I, CL. 2. -- NAVY QPD (QUALIFIED PRODUCTS DATABASE)
PT-500K Epoxy Primer is a low VOC epoxy polyamide solvent primer on the Navy QPD as PT-500 GIC. .PT-500KIC2 TY 1 CL. 2 is highly recommended for use on aluminum and other metallic surfaces to insure maximum protection against corrosion. PT-500K Epoxy Primer also insures maximum adhesion of PTI TUF/FILM coating, polyurethane, epoxy, enamel, lacquer or any finish coats. This Primer is intended to be used for aircraft, marine, original equipment manufacturing and all other industrial applications.
PT-522 ZINC CHROMATE PRIMER
Part Number: PT-522 Yellow or Green Chromate/Non-Chromate
Military Specification: TT-P-1757 TYI CLASS C & N
PT-522 Zinc Chromate Primer — TT-P-1757 TYI CLASS C & N is a general purpose, rust inhibitive, alkyd primer. It is intended for use over metals that are bare, scuffed, sanded, lightly rusted, abrasive blast and previously painted surfaces while showing excellent anti-corrosion properties. The primer chemically etches into the surface to provide exceptional adhesion and durability. Also, moisture in the air causes the zinc chromate to react with the metal surface, and it forms a passive film that prevents corrosion. Although this primer is intended for metals, it may be applied to wood, composite and concrete surfaces. PT-522 is not resistant to all solvents, i.e. MEK and Acetone.
PT-573 - FILLER/SANDING PRIMER
Part Number: PT-573
Military Specification: Not a MIL-SPEC Coating
PT-573 Filler/ Sanding Epoxy Primer is a two component epoxy based primer. PT-573 is capable of filling small holes and imperfections before top coating. PT-573 provides a smooth, sandable base coat that improves the adhesion and appearance of the top coat. Because of PT-573’s unique formula, this primer also provides excellent rust and corrosion protection. This primer is compatible with PTI’s topcoats.
PT-605 ANTI-SEIZE COMPOUND
Part Number: PT-605
Military Specification: NOT A MIL-SPEC COATING
PT-605 Anti-Seize Compound is a silicone based grease with a high pigmentation of microfine molybdenum disulfide. It is heat stable and will not decompose or form a gum deposit. It is effective under light or medium bearing loads on steel to bronze, metal babbitt, zinc, nylon, Teflon or hard-anodized aluminum surfaces. PT-605 is an EXTREME PRESSURE grease that protects from galling, seizing and fretting. Also this product is virtually waterproof which helps to provide excellent rust and corrosion protection. Normally it is suitable for operating temperatures of -65° F to +1000° F. This product is best used as a lubricant for gaskets threads, parts and gears that are exposed to excessive temperatures ranges.
PT-650 TOOTH MARKING GREASE
Part Number: PT-650
Military Specification: NOT A MIL-SPEC COATING
PT-650 Tooth Marking Grease is an ester based oil with high pigmentation loading. Although PT-650 has the consistency of a thick paste, it may be thinned or thickened to meet your requirements. PT-650 is a lubricant for marking teeth on gears to enable one to determine when maintenance is necessary.
PT-799 - POLYURETHANE
Part Number: PT-799 (PLUS COLOR#)
Military Specification: MIL-PRF-85285D/E Type I, II & IV Class H. This coating is on the NAVY QPD (Qualified Products Database) for TY I, II & IV (gloss only)
PT-799 Polyurethane is a high performance, two-component, polyurethane topcoat designed for exterior use on high performance, general aviation, business jet, and commercial aircraft. This coating is also used widely for industrial, oil and gas as well as by original equipment manufacturers. These high performance coatings have excellent resistance to hydraulic jet fluid, fuel, crude oil, impact, salt and ultraviolet rays. PT-799 Polyurethane is extremely durable with excellent color and gloss retention.
PT-799 Conductive Black is also available. It is formulated as an electrically conductive paint which can be used for coating and sealing non-metallic surfaces by brushing or spraying. The Conductive Coating is intended for use where an electrostatic discharge path is required for electrical continuity on non-metallic substrates.
PTW-582 WATER REDUCIBLE EPOXY PRIMER
Part Number: PTW-582
Military Specification: MIL-PRF -85582D. BMS 10-11Y TY I, CL A, GR E. -- NAVY QPD (QUALIFIED PRODUCTS DATABASE)
PTW-582 Water Reducible Epoxy Primer is chemical and solvent resistant. It is especially recommended to inhibit corrosion of aluminum and other plated or unplated metallic surfaces. PTI’s Water Reducible Epoxy Primer is recommended for all PTI topcoats to provide maximum adhesion and corrosion protection.
Primer Coatings: Epoxy, Waterborne
RED OXIDE ALKYD PRIMER
RED OXIDE FAST DRY ALKYD PRIMER LEAD & CHROMATE FREE, VOC COMPLIANT
RED OXIDE PRIMER
RETARDER ADDITIVE FOR PAINTS AND PRIMERS
Remover, Paint, No Hazardous Air Pollutants (HAPS)
SEALER FOR EPOXY ANTI-GRAFFITI COATING
2000°f HIGH TEMP. THERMAL LAG COATING
SILICONE ALKYD
HIGH TEMPERATURE THERMAL LAG COATING
SILICONE RUBBER COATING
SLOW EVAPORATING THINNER/REDUCER
ETHYL ALCHOL; DENATURED ALCOHOL; ETHANOL 200
SOLVENT THINNED ENAMEL
XYLENE
