CLOSE ✕
Get in Touch
Thank you for your interest! Please fill out the form below if you would like to work together.

Thank you! Your submission has been received!

Oops! Something went wrong while submitting the form

AEROSOL NITROCELLULOSE LACQUER

|
LACQUERS
|
A-A-665D
PTI has divested its specialty coatings and solvents, including the PTI and Certified Coatings product lines, to SOCOMORE. Click here for more details on the acquisition, click here to place an order or register, or reach out directly at csr-na@socomore.com.
A-A-665D
AEROSOL NITROCELLULOSE LACQUER

AEROSOL NITROCELLULOSE LACQUER

A-A-665D is a nitrocellulose lacquer that is packaged in an aerosol can. This lacquer is intended for use on metal or composite surfaces.

PRODUCT SPECIFICATIONS
PTI PART NUMBER
A-A-665D
PRODUCT TYPE:
LACQUERS
COLOR:
BMS SPECIFICATION:
NONE
MIL-SPEC:
A-A-665D
OTHER SPECIFICATIONS
NONE
UNIT SIZE
AEROSOL

Extended Description

A-A-665D is a nitrocellulose lacquer that is packaged in an aerosol can. This lacquer is intended for use on metal or composite surfaces.

COLORS

This coating can be provided in any color & gloss range as designated by the Federal Standard 595C. Custom colors are also available.

COATING PROPERTIES & CHARACTERISTICS

  • Primer: PT-522
  • Recommended Dry Film Thickness: 1 mil
  • Weight (lbs per gallon): 9 to 10 lbs
  • Coatings VOC: Below 409 to 685 g/L

SHELF LIFE

Shelf life is only applicable for materials stored in unopened and undamaged original factory filled containers.1 year when stored between 50⁰-85⁰ Fahrenheit.

APPLICATION

This product can be applied by aerosol can.

  1. Shake the aerosol can, right side up, for a minimum of 60 seconds.
  2. Turn the can upside down and shake.
  3. After the product in shaken thoroughly you may apply by pressing on the spray nozzle.
  4. Repeat shaking after every minute of spraying
  5. After every use, turn the can upside down and press the nozzle down until the spray coming out is clear. This means that the nozzle is clear and has a lesser chance of clogging between uses.

NOTE: Application of PTI products requires the use of all OSHA approved safety equipment, including proper ventilation. Additionally, PTI products require the recommended temperature/humidity conditions and film thickness ranges for optimal performance. The material, hangar, and aircraft skin temperatures should be no lower than 75⁰ F / 25⁰ C before, during and after application.

DRYING & CURING SCHEDULE

Dry times are based on the dry film thickness between 1-2 mils (25-50 microns).

Air Dry Times (75⁰F / 25⁰C and 50% Relative Humidity)

  • Set to touch 15 minutes
  • Dry through 2 hours

EQUIPMENT CLEANUP

Use clean PT-1022X66, Acetone or IPA. Do not allow material to dry or cure inside any equipment.

HEALTH, SAFETY, & STORAGE REQUIREMENTS

Refer to each individual material SDS (Safety Data Sheet) for specific requirements on the health, safety, storage and handling requirements. Follow all local, state, and national regulations during surface preparation, material application and cleanup.PRODUCT INFORMATION & DISCLAIMERProduct Data Sheets are periodically updated to reflect new information. It is important to use the latest and most recent revision for the product being used. The foregoing information is accurate to the best of our knowledge.However, due to differences in customer handling, use and method of application which are not known and are beyond our control, Products Techniques, Inc. makes no warranties as to the end result.

Questions About Our Products?
Contact PTI

More PTI Products